ISO 3001 to ISO 3994

ISO 3001 to ISO 3994
ISO 3001:1999Plastics. Epoxy compounds. Determination of epoxy equivalent
ISO 3007:1999Methods of test for petroleum and its products. 2000-69. Petroleum products. Determination of vapour pressure. Reid method
ISO 3011:1997Rubber- or plastics-coated fabrics. Determination of resistance to ozone cracking under static conditions
ISO 3019-1:2001Hydraulic fluid power. Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors. Inch series shown in metric units
ISO 3019-2:2001Hydraulic fluid power. Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors. Metric series
ISO 3022:1988Cinematography. 35 mm motion-picture film perforated 16 mm (1-3-0). Cutting and perforating dimensions
ISO 3023:1995Cinematography. 65 mm and 70 mm unexposed motion-picture film. Cutting and perforating dimensions
ISO 3026:1992Cinematography. Printed 8 mm Type S image area on 35 mm motion-picture film perforated 8 mm Type S, 2R-4.227 (1664) or 5R-4.234 (1667). Position and dimensions
ISO 3027:1984Cinematography. Magnetic stripes and recording head gaps for sound record on 8 mm Type S motion-picture films. Position and width dimensions
ISO 3029:1995Photography. 126 size cartridges. Dimensions of cartridge, film and backing paper
ISO 3030:1996Rolling bearings. Radial needle roller and cage assemblies. Dimensions and tolerances
ISO 3031:2000Rolling bearings. Thrust needle roller and cage assemblies, thrust washers. Boundary dimensions and tolerances
ISO 3037:1996Corrugated fibreboard. Determination of edgewise crush resistance (unwaxed edge method)
ISO 3040:1990Technical drawings. Dimensioning and tolerancing. Cones
ISO 3046-1:2002Reciprocating internal combustion engines. Performance. Declarations of power, fuel and lubricating oil consumptions, and test methods. Additional requirements for engines for general use
ISO 3046-5:2001Reciprocating internal combustion engines. Performance. Torsional vibrations
ISO 3057:1998Non-destructive testing. Metallographic replica techniques of surface examination
ISO 3058:1998Non-destructive testing. Aids to visual inspection. Selection of low-power magnifiers
ISO 3059:2001Non-destructive testing. Penetrant testing and magnetic particle testing. Viewing conditions
ISO 3068:1982Cinematography. Magnetic stripes for sound records on 16 mm motion-picture film perforated 8 mm Type S-2R (1-4) and (1-3). Positions and width dimensions
ISO 3069:2000End-suction centrifugal pumps. Dimensions of cavities for mechanical seals and for soft packing
ISO 3070-2:1997Test conditions for boring and milling machines with horizontal spindle. Testing of the accuracy. Table-type machines
ISO 3070-3:1997Test conditions for boring and milling machines with horizontal spindle. Testing of the accuracy. Floor type machines with detached, stationary work-holding table
ISO 3070-4:1998Test conditions for boring and milling machines with horizontal spindle. Testing of the accuracy. Planer type machines with movable column
ISO 3085:2002Iron ores. Experimental methods for checking the precision of sampling, sample preparation and measurement
ISO 3086:1998Iron ores. Experimental methods for checking the bias of sampling
ISO 3087:1998Iron ores. Determination of the moisture content of a lot
ISO 3096:1996Rolling bearings. Needle rollers. Dimensions and tolerances
ISO 3098-0:1998Technical product documentation. Lettering. General requirements
ISO 3098-2:2000Technical product documentation. Lettering. Latin alphabet, numerals and marks
ISO 3098-3:2000Technical product documentation. Lettering. Greek alphabet
ISO 3098-4:2000Technical product documentation. Lettering. Diacritical and particular marks for the Latin alphabet
ISO 3098-5:1998Technical product documentation. Lettering. CAD lettering of the Latin alphabet, numerals and marks
ISO 3098-6:2000Technical product documentation. Lettering. Cyrillic alphabet
ISO 3104:1996Methods of test for petroleum and its products. Petroleum products. Transparent and opaque liquids. Determination of kinematic viscosity and calculation of dynamic viscosity
ISO 3116:2001Magnesium and magnesium alloys. Wrought magnesium alloys
ISO 3146:2000Plastics. Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods
ISO 3160-1:1998Watch-cases and accessories. Gold alloy coverings. General requirements
ISO 3160-2:2003Watch-cases and accessories. Gold alloy coverings. Determination of fineness, thickness, corrosion resistance and adhesion
ISO 3164:2000Earth-moving machinery. Laboratory evaluations of protective structures. Specifications for deflection-limiting volume
ISO 3166-1:1998Codes for the representation of names of countries and their subdivisions. Country codes
ISO 3166-2:1998Codes for the representation of names of countries and their subdivisions. Country subdivision code
ISO 3166-3:1999Codes for the representation of names of countries and their subdivisions. Code for formerly used names of countries
ISO 3167:2003Plastics. Multipurpose test specimens
ISO 3170:1999Petroleum liquids. Manual sampling
ISO 3171:1999Petroleum liquids. Automatic pipeline sampling
ISO 3175-1:1998Textiles. Dry cleaning and finishing. Method for assessing the cleanability of textiles and garments
ISO 3175-2:1998Textiles. Dry cleaning and finishing. Procedures for tetrachloroethene
ISO 3183-3:1999Petroleum and natural gas industries. Steel pipe for pipelines. Technical delivery conditions. Pipes of requirement class C
ISO 3188:1994Starches and derived products. Determination of nitrogen content by the Kjeldahl method. Titrimetric method
ISO 3218:1976Essential oils. Principles of nomenclature
ISO 3219:1995Plastics. Polymers/resins in the liquid state or as emulsions or dispersions. Determination of viscosity using a rotational viscometer with defined shear rate
ISO 3231:1998Paints and varnishes. Determination of resistance to humid atmospheres containing sulfur dioxide
ISO 3245:1997Rolling bearings. Needle roller bearings, drawn cup without inner rings. Boundary dimensions and tolerances
ISO 3248:2001Paints and varnishes. Determination of the effect of heat
ISO 3251:2003Paints, varnishes and plastics. Determination of non-volatile-matter content
ISO 3252:2000Powder metallurgy. Vocabulary
ISO 3262-1:1998Extenders for paints. Specifications and methods of test. Introduction and general test methods
ISO 3262-2:1998Extenders for paints. Specifications and methods of test. Barytes (natural barium sulfate)
ISO 3262-3:1998Extenders for paints. Specifications and methods of test. Blanc fixe
ISO 3262-4:1998Extenders for paints. Specifications and methods of test. Whiting
ISO 3262-5:1998Extenders for paints. Specifications and methods of test. Natural crystalline calcium carbonate
ISO 3262-6:1998Extenders for paints. Specifications and methods of test. Precipitated calcium carbonate
ISO 3262-7:1998Extenders for paints. Specifications and methods of test. Dolomite
ISO 3262-8:2000Extenders for paints. Specifications and methods of test. Natural clay
ISO 3262-9:1998Extenders for paints. Specifications and methods of test. Calcined clay
ISO 3262-10:2000Extenders for paints. Specifications and methods of test. Natural talc/chlorite in lamellar form
ISO 3262-11:2000Extenders for paints. Specifications and methods of test. Natural talc, in lamellar form, containing carbonates
ISO 3262-12:2001Extenders for paints. Specifications and methods of test. Muscovite-type mica
ISO 3262-13:1998Extenders for paints. Specifications and methods of test. Natural quartz (ground)
ISO 3262-14:2000Extenders for paints. Specifications and methods of test. Cristobalite
ISO 3262-15:2000Extenders for paints. Specifications and methods of test. Vitreous silica
ISO 3262-16:2000Extenders for paints. Specifications and methods of test. Aluminium hydroxides
ISO 3262-17:2000Extenders for paints. Specifications and methods of test. Precipitated calcium silicate
ISO 3262-18:2000Extenders for paints. Specifications and methods of test. Precipitated sodium aluminium silicate
ISO 3262-19:2000Extenders for paints. Specifications and methods of test. Precipitated silica
ISO 3262-20:2000Extenders for paints. Specifications and methods of test. Fumed silica
ISO 3262-21:2000Extenders for paints. Specifications and methods of test. Silica sand (unground natural quartz)
ISO 3262-22:2001Extenders for paints. Specifications and methods of test. Flux-calcined kieselguhr
ISO 3269:2001Fasteners. Acceptance inspection
ISO 3271:1995Iron ores. Determination of tumble strength
ISO 3272-1:2003Microfilming of technical drawings and other drawing office documents. Operating procedures
ISO 3272-2:1994Microfilming of technical drawings and other drawing office documents. Quality criteria and control of 35 mm silver gelatin microfilms
ISO 3272-3:2001Microfilming of technical drawings and other drawing office documents. Aperture card for 35 mm microfilm
ISO 3272-4:1994Microfilming of technical drawings and other drawing office documents. Microfilming of drawings of special and exceptional elongated sizes
ISO 3272-5:1999Microfilming of technical drawings and other drawing office documents. Test procedures for diazo duplicating of microfilm images in aperture cards
ISO 3272-6:2000Microfilming of technical drawings and other drawing office documents. Quality criteria and control of systems for enlargement from 35mm microfilm
ISO 3274:1998Geometric product specifications (GPS). Surface texture. Profile method. Nominal characteristics of contact (stylus) instruments
ISO 3287:1999Powered industrial trucks. Symbols for operator controls and other displays
ISO 3290:2001Rolling bearings. Balls. Dimensions and tolerances
ISO 3298:1994Photography. Processing chemicals. Specifications for glacial acetic acid
ISO 3299:1994Photography. Processing chemicals. Specifications for 1-phenyl-3-pyrazolidinone
ISO TR 3313:1998Measurement of fluid flow in closed conduits. Guidelines on the effects of flow pulsations on flow-measurement instruments
ISO 3322:1985Fluid power systems and components. Cylinders. Nominal pressures
ISO 3325:1999Sintered metal materials, excluding hardmetals. Determination of transverse rupture strength
ISO 3336:1996Dentistry. Synthetic polymer teeth
ISO 3338-1:1996Cylindrical shanks for milling cutters. Dimensional characteristics of plain cylindrical shanks
ISO 3338-2:1996Cylindrical shanks for milling cutters. Dimensional characteristics of flatted cylindrical shanks
ISO 3341:2000Textile glass. Yarns. Determination of breaking force and breaking elongation
ISO 3342:1995Textile glass. Mats. Determination of tensile breaking force
ISO 3344:1997Reinforcement products. Determination of moisture content
ISO 3366:1999Coated abrasives. Abrasive rolls
ISO 3374:2000Reinforcement products. Mats and fabrics. Determination of mass per unit area
ISO 3376:2002Leather. Physical and mechanical tests. Determination of tensile strength and percentage extension
ISO 3377-1:2002Leather. Physical and mechanical tests. Determination of tear load. Single edge tear
ISO 3377-2:2002Leather. Physical and mechanical tests. Determination of tear load. Double edge tear
ISO 3378:2002Leather. Physical and mechanical tests. Determination of resistance to grain cracking and grain crack index
ISO 3380:2002Leather. Physical and mechanical tests. Determination of shrinkage temperature up to 100 degrees C
ISO 3382:2000Acoustics. Measurement of the reverberation time of rooms with reference to other acoustical parameters
ISO 3384:1999Rubber, vulcanized or thermoplastic. Determination of stress relaxation in compression at ambient and at elevated temperatures
ISO 3385:1995Flexible cellular polymeric materials. Determination of fatigue by constant-load pounding
ISO 3386-1:1998Polymeric materials, cellular flexible. Determination of stress-strain characteristic in compression. Low-density materials
ISO 3386-2:1998Polymeric materials, cellular flexible. Determination of stress-strain characteristic in compression. High-density materials
ISO 3405:2000Methods of test for petroleum and its products. Petroleum products. Determination of distillation characteristics at atmospheric pressure
ISO 3411:2000Earth-moving machinery. Human physical dimensions of operators and minimum operator space envelope
ISO 3450:1996Safety of earth-moving machinery. Specification for braking systems and performance requirements and test procedures for rubber-tyred machines
ISO 3451-1:1997Plastics. Determination of ash. General methods
ISO 3451-4:2000Plastics. Determination of ash. Polyamides
ISO 3451-5:2002Plastics. Determination of ash. Poly(vinyl chloride)
ISO 3452-2:2000Non-destructive testing. Penetrant testing. Testing of penetrant materials
ISO 3452-3:1999Non-destructive testing. Penetrant testing. Reference test blocks
ISO 3452-4:1999Non-destructive testing. Penetrant testing. Equipment
ISO 3457:1995Earth-moving machinery. Guards and shields. Definitions and specifications
ISO 3497:2001Metallic coatings. Measurement of coating thickness. X-ray spectrometric methods
ISO 3506-1:1998Mechanical properties of corrosion-resistant stainless-steel fasteners. Bolts, screws and studs
ISO 3506-2:1998Mechanical properties of corrosion-resistant stainless-steel fasteners. Nuts
ISO 3506-3:1998Mechanical properties of corrosion-resistant stainless-steel fasteners. Set screws and similar fasteners not under tensile stress
ISO 3506-4:2003Mechanical properties of corrosion-resistant stainless-steel fasteners. Tapping screws
ISO 3507:1999Laboratory glassware. Pyknometers
ISO 3521:2000Plastics. Unsaturated polyester and epoxy resins. Determination of overall volume shrinkage
ISO 3534-1:1993Statistics. Vocabulary and symbols. Probability and general statistical terms
ISO 3534-2:1993Statistics. Vocabulary and symbols. Statistical quality control
ISO 3534-3:1999Statistics. Vocabulary and symbols. Design of experiments
ISO 3543:2001Metallic and non-metallic coatings. Measurement of thickness. Beta backscatter method
ISO 3547-1:1999Plain bearings. Wrapped bushes. Dimensions
ISO 3547-2:1999Plain bearings. Wrapped bushes. Test data for outside and inside diameter
ISO 3547-3:1999Plain bearings. Wrapped bushes. Lubrication holes, lubrication grooves and lubrication indentations
ISO 3547-4:1999Plain bearings. Wrapped bushes. Materials
ISO 3548:1999Plain bearings. Thin-walled half bearings with or without flange. Tolerances, design features and methods of test
ISO 3549:2002Zinc dust pigments for paints. Specifications and test methods
ISO 3553-2:1997Road vehicles. High tension connectors for ignition coils and distributors. Plug types
ISO 3582:2001Flexible cellular polymeric materials. Laboratory assessment of horizontal burning characteristics of small specimens subjected to a small flame
ISO 3585:1998Borosilicate glass 3.3. Properties
ISO 3593:1994Starch. Determination of ash
ISO 3596:2001Animal and vegetable fats and oils. Determination of unsaponifiable matter. Method using diethyl ether extraction
ISO 3613:2001Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys. Test methods
ISO 3616:2001Textile glass. Chopped-strand and continuous-filament mats. Determination of average thickness, thickness under load and recovery after compression
ISO 3617:1994Photography. Processing chemicals. Specifications for sodium hydroxide
ISO 3618:1994Photography. Processing chemicals. Specifications for benzotriazole
ISO 3619:1994Photography. Processing chemicals. Specification for ammonium thiosulfate solution
ISO 3620:1994Photography. Processing chemicals. Specifications for aluminium potassium sulfate
ISO 3621:1994Photography. Processing chemicals. Specifications for sodium tetraborate decahydrate
ISO 3622:1996Photography. Processing chemicals. Specifications for ammonium thiocyanate
ISO 3623:1994Photography. Processing chemicals. Specifications for anhydrous potassium carbonate
ISO 3624:1994Photography. Processing chemicals. Specifications for potassium ferricyanide
ISO 3625:1994Photography. Processing chemicals. Specifications for potassium hydroxide
ISO 3626:1996Photography. Processing chemicals. Specification for potassium thiocyanate
ISO 3627:2001Photography. Processing chemicals. Specifications for anhydrous sodium metabisulfite
ISO 3628:1994Photography. Processing chemicals. Specifications for boric acid, granular
ISO 3629:2000Photography. Processing chemicals. Specifications for potassium metabisulfite
ISO 3630-1:1995Dental root-canal instruments. Files, reamers, barbed broaches, rasps, paste carriers, explorers and cotton broaches
ISO 3630-2:2001Dental root-canal instruments. Enlargers
ISO 3630-3:1997Dental root-canal instruments. Condensers, pluggers and spreaders
ISO 3639:1981Cinematography. Projection reels/spools 75 to 312 mm diameter for 8 mm Type S motion-picture film. Dimensions and specifications
ISO 3645:1984Cinematography. Image area produced by 8 mm Type S motion-picture camera aperture and maximum projectable image area. Positions and dimensions
ISO 3650:1999Geometrical product specifications (GPS). Length standards. Gauge blocks
ISO 3651-1:1998Determination of resistance to intergranular corrosion of stainless steels. Austenitic and ferritic-austenitic (duplex) stainless steels. Corrosion test in nitric acid medium by measurement of loss in mass (Huey test)
ISO 3651-2:1998Determination of resistance to intergranular corrosion of stainless steels. Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels. Corrosion test in media containing sulfuric acid
ISO 3656:2002Animal and vegetable fats and oils. Determination of ultraviolet absorbance expressed as specific UV extinction
ISO 3657:2002Animal and vegetable fats and oils. Determination of saponification value
ISO 3664:2000Viewing conditions for graphic technology and photography
ISO 3665:1996Photography. Intra-oral dental radiographic film. Specification
ISO/TR 3666:1998Viscosity of water
ISO 3668:2001Paints and varnishes. Visual comparison of the colour of paints
ISO 3671:1999Plastics. Aminoplastic moulding materials. Determination of volatile matter
ISO 3672-1:2001Plastics. Unsaturated-polyester resins (UP-R). Designation system
ISO 3672-2:2001Plastics. Unsaturated-polyester resins (UP-R). Preparation of test specimens and determination of properties
ISO 3673-1:2000Plastics. Epoxy resins. Designation
ISO 3673-2:2000Plastics. Epoxy resins. Preparation of test specimens and determination of properties
ISO 3675:1998Crude petroleum and liquid petroleum products. Laboratory determination of density. Hydrometer method
ISO 3677:1995Filler metal for soft soldering, brazing and braze welding. Designation
ISO 3678:1995Paints and varnishes. Print-free test
ISO 3681:1998Binders for paints and varnishes. Determination of saponification value. Titrimetric method
ISO 3682:1998Binders for paints and varnishes. Determination of acid value. Titrimetric method
ISO 3686-1:2000Test conditions for high accuracy turret and single spindle coordinate drilling and boring machines with table of fixed height with vertical spindle. Testing of the accuracy. Single column type machines
ISO 3686-2:2000Test conditions for high accuracy turret and single spindle coordinate drilling and boring machines with table of fixed height with vertical spindle. Testing of the accuracy. Portal type machines with moving table
ISO 3688:1999Pulps. Preparation of laboratory sheets for the measurement of diffuse blue reflectance factor (ISO brightness)
ISO 3690:2001Welding and allied processes. Determination of hydrogen content in ferritic steel arc weld metal
ISO 3696:1995Water for analytical laboratory use. Specification and test methods
ISO 3715-2:2001Ships and marine technology. Propulsion plants for ships. Vocabulary for controllable-pitch propeller plants
ISO 3723:1976Hydraulic fluid power. Filter elements. Method for end load test
ISO 3724:1976Hydraulic fluid power. Filter elements. Verification of flow fatigue characteristics
ISO 3727-1:2002Butter. Determination of moisture, non-fat solids and fat contents. Determination of moisture content (Reference method)
ISO 3727-2:2002Butter. Determination of moisture, non-fat solids and fat contents. Determination of non-fat solids content (Reference method)
ISO 3727-3:2003Butter. Determination of moisture, non-fat solids and fat contents. Calculation of fat content
ISO 3735:1999Crude petroleum and fuel oils. Determination of sediment. Extraction method
ISO 3740:2001Acoustics. Determination of sound power levels of noise sources. Guidelines for the use of basic standards
ISO 3741:2000Acoustics. Determination of sound power levels of noise sources using sound pressure. Precision methods for reverberation rooms
ISO 3743-1:1995Acoustics. Determination of sound power levels of noise sources. Engineering methods for small, movable sources in reverberant fields. Comparison for hard-walled test rooms
ISO 3743-2:1997Acoustics. Determination of sound power levels of noise sources. Engineering methods for small, movable sources in reverberant fields. Methods for special reverberation test rooms
ISO 3744:1995Acoustics. Determination of sound power levels of noise sources using sound pressure. Engineering method in an essentially free field over a reflecting plane
ISO 3746:1996Acoustics. Determination of sound power levels of noise sources using sound pressure. Survey method using an enveloping measurement surface over a reflecting plane
ISO 3747:2000Acoustics. Determination of sound power levels of noise sources using sound pressure. Comparison method in situ
ISO 3759:1995Textiles. Preparation, marking and measuring of fabric specimens and garments in tests for determination of dimensional change
ISO 3764:2000Timekeeping instruments. Movements. Forms, dimensions and nomenclature
ISO 3766:1999Construction drawings. Simplified representation of concrete reinforcement
ISO 3767-1:2000Tractors, machinery for agriculture and forestry, powered lawn and garden equipment. Symbols for operator controls and other displays. Common symbols (review)
ISO 3767-2:1996Tractors, machinery for agriculture and forestry, powered lawn and garden equipment. Symbols for operator controls and other displays. Symbols for agricultural tractors and machinery
ISO 3767-3:1996Tractors, machinery for agriculture and forestry, powered lawn and garden equipment. Symbols for operator controls and other displays. Symbols for powered lawn and garden equipment
ISO 3767-4:1996Tractors, machinery for agriculture and forestry, powered lawn and garden equipment. Symbols for operator controls and other displays. Symbols for forestry machinery
ISO 3767-5:1992Tractors, machinery for agriculture and forestry, powered lawn and garden equipment. Symbols for operator controls and other displays. Symbols for manual portable forestry machinery
ISO 3772:2000Photography. Rolls of sensitized material for the pre-press industry. Dimensions and related requirements
ISO 3773:1983Cinematography. Tape splices for 8 mm Type S motion-picture film for projector use. Dimensions
ISO 3774:1988Cinematography. 35 mm motion-picture film perforated 8 mm Type S (1-3-5-7-0) and (1-0). Cutting and perforating dimensions
ISO 3775:1990Cinematography. Printed 8 mm Type S image area on 16 mm motion-picture film perforated 8 mm Type S (1-3). Position and dimensions
ISO 3785:1995Steel. Designation of test piece axes
ISO/IEC 3788:1990Information processing. 9-track, 12,7 mm (0,5 in) wide magnetic tape for information interchange using phase encoding at 126 ftpmm (3200 ftpi) - 63 cpmm (1600 cpi)
ISO 3793:1976Essential oils. Estimation of primary and secondary free alcohols content by acetylation in pyridine
ISO 3794:1976Essential oils (containing tertiary alcohols). Estimation of free alcohols content by determination of ester value after acetylation
ISO 3796:2001Ships and marine technology. Clear openings for external single-leaf doors
ISO 3808:2002Road vehicles. Unscreened high-voltage ignition cables. General specifications, test methods and requirements
ISO 3822-1:1999Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Method of measurement
ISO 3822-2:1996Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Mounting and operating conditions for draw-off taps and mixing valves
ISO 3822-3:1997Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Mounting and operating conditions for in-line valves and appliances
ISO 3822-4:1997Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Mounting and operating conditions for special appliances
ISO 3823-1:1999Dental rotary instruments. Burs. Steel and carbide burs
ISO 3823-2:2003Dental rotary instruments. Burs. Finishing burs
ISO 3830:1996Petroleum products. Determination of lead content of gasoline. Iodine monochloride method
ISO 3838:1996Methods for determination of density or relative density of petroleum and petroleum products (pyknometer methods)
ISO 3849:2003Oil of citronella, Sri Lanka type [$7ICymbopogon nardus$7R (L.) W. Watson var. $7Ilenabatu$7R Stapf.]
ISO 3861:1997Rubber hoses for sand and grit blasting. Specification
ISO 3865:1997Rubber, vulcanized or thermoplastic. Methods of test for staining in contact with organic material
ISO 3867:2001Composition cork. Expansion joint fillers. Test methods
ISO 3868:1995Metallic and other non-organic coatings. Measurement of coating thicknesses. Fizeau multiple-beam interferometry method
ISO 3869:2001Composition cork. Expansion joint fillers. Specifications, packaging and marking
ISO 3874:1997Series 1 freight containers. Handling and securing
ISO 3882:2003Metallic and other inorganic coatings. Review of methods of measurement of thickness
ISO 3887:2003Steels. Determination of depth of decarburization
ISO 3888-1:1999Passenger cars. Test track for a severe lane-change manoeuvre. Double-lane change
ISO 3888-2:2002Passenger cars. Test track for a severe lane-change manoeuvre. Obstacle avoidance
ISO 3890-1:2000Milk and milk products. Determination of residues of organochlorine compounds (pesticides). General considerations and extraction methods
ISO 3890-2:2000Milk and milk products. Determination of residues of organochlorine compounds (pesticides). Test methods for crude extract purification and confirmation
ISO 3892:2001Conversion coatings on metallic materials. Determination of coating mass per unit area. Gravimetric methods
ISO 3901:2001Information and documentation. International Standard Recording Code (ISRC)
ISO 3915:1999Plastics. Measurement of resistivity of conductive plastics
ISO 3918:1996Milking machine installations. Vocabulary
ISO 3927:2002Metallic powders, excluding powders for hardmetals. Determination of compressbility in uniaxial compression
ISO 3928:1999Sintered metal materials, excluding hardmetals. Fatigue test pieces
ISO 3943:1993Photography. Processing chemicals. Specifications for anhydrous sodium acetate
ISO 3946:1994Starches and derived products. Determination of total phosphorus content. Spectrometric method
ISO 3947:1994Starches, native or modified. Determination of total fat content
ISO 3950:1997Dentistry. Designation system for teeth and areas of the oral cavity
ISO 3952-1:1995Kinematic diagrams. Graphical symbols. Part 1
ISO 3952-2:1995Kinematic diagrams. Graphical symbols. Part 2
ISO 3952-3:1995Kinematic diagrams. Graphical symbols. Part 3
ISO 3952-4:1997Kinematic diagrams. Graphical symbols. Miscellaneous mechanisms and their components
ISO 3953:1995Metallic powders. Determination of tap density
ISO 3961:2000Animal and vegetable fats and oils. Determination of iodine value
ISO 3968:2001Hydraulic fluid power. Filters. Evaluation of differential pressure versus flow characteristics
ISO 3977-4:2002Gas turbines. Procurement. Fuels and environment
ISO 3977-5:2003Gas turbines. Procurement. Applications for petroleum and natural gas industries
ISO 3977-7:2002Gas turbines. Procurement. Technical information
ISO 3977-8:2002Gas turbines. Procurement. Inspection, testing, installation and commissioning
ISO 3993:1996Liquefied petroleum gas and light hydrocarbons. Determination of density or relative density. Pressure hydrometer method
ISO 3994:2001Plastics hoses. Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials. Specification